Publish two packages x86_64: chan-pbx-sat (driver) + pbxsat-freepbx (GUI)

- chan-pbx-sat: driver .so + pbx_sat.conf.sample (current config) + HOWTO.
- pbxsat-freepbx: FreePBX web GUI (admin module + dashboard widget), deb arch=all
  / rpm noarch, deploys via fwconsole, depends on chan-pbx-sat.
Debian 12/13 (bookworm/trixie) + CentOS/RHEL 7(ast16,ast18)/8/9. README updated.

README.md

@@ -2,27 +2,43 @@
 
 Prebuilt **`.deb`** and **`.rpm`** packages for
 **[pbx_sat](https://git.sa7aux.se/bjorne/pbx-sat)**, the direct PBX ↔ SVXReflector
-bridge channel driver (`chan_pbx_sat`) — no AllStar in the path.
+bridge (`chan_pbx_sat`) — no AllStar in the path. Install these to build your own
+PBX ↔ SVX trunk.
 
 This repo holds **only built packages**, no source. The source lives in the
-private `pbx-sat` repo.
+private `pbx-sat` repo. **x86_64 only** (PBX boxes are x86).
 
-## Debian / Ubuntu / Raspberry Pi (`debs/`)
+Two packages:
+
+- **`chan-pbx-sat`** — the driver (`chan_pbx_sat.so`) + a sample
+  `/etc/asterisk/pbx_sat.conf` and the setup guide. Works on any Asterisk box.
+- **`pbxsat-freepbx`** — the **FreePBX web GUI** (admin module *Connectivity →
+  PBX ⇄ SVX* + a dashboard status widget). Install it **too** on a FreePBX box;
+  it deploys into the web root via `fwconsole` and depends on `chan-pbx-sat`.
+  Not needed on a plain-Asterisk box (configure `pbx_sat.conf` by hand).
+
+## Debian 12 / 13 (`debs/`)
 
 ```sh
-sudo apt install ./debs/chan-pbx-sat_<version>~<suite>_<arch>.deb
+# the driver (required):
+sudo apt install ./debs/chan-pbx-sat_<version>~<suite>_amd64.deb
+# the FreePBX GUI (on a FreePBX box):
+sudo apt install ./debs/pbxsat-freepbx_<version>~<suite>_all.deb
 ```
 
-`<suite>` is `bookworm` or `trixie`, `<arch>` is `amd64` (x86-64) or `arm64`
-(Raspberry Pi). Built against Asterisk 22.
+`<suite>` is `bookworm` (Debian 12) or `trixie` (Debian 13). Built against the
+box's Asterisk.
 
-## CentOS / RHEL (`rpms/`, x86_64)
+## CentOS / RHEL 7 / 8 / 9 (`rpms/`)
 
 ```sh
+# the driver (required):
 sudo dnf install ./rpms/chan-pbx-sat-<version>.<asttag>.<dist>.x86_64.rpm
+# the FreePBX GUI (on a FreePBX box):
+sudo dnf install ./rpms/pbxsat-freepbx-<version>.<asttag>.<dist>.noarch.rpm
 ```
 
-One RPM per (distro, Asterisk major):
+One driver RPM per (distro, Asterisk major):
 
 | File | Distro | Asterisk |
 |------|--------|----------|
@@ -31,4 +47,14 @@ One RPM per (distro, Asterisk major):
 | `…ast18.el7…` | CentOS Linux 7  | 18 |
 | `…ast16.el7…` | CentOS Linux 7  | 16 |
 
-See the source repo for setup and the design write-up.
+## After install
+
+The driver does not load until you enable it:
+
+1. `cp /etc/asterisk/pbx_sat.conf.sample /etc/asterisk/pbx_sat.conf` and edit it
+   (or use the FreePBX GUI if you installed `pbxsat-freepbx`).
+2. Uncomment `load = chan_pbx_sat.so` in `/etc/asterisk/modules.conf`.
+3. Point a dialplan route at `PBXSAT/<trunk>/<tg>`.
+4. `asterisk -rx "core restart now"` then `asterisk -rx "pbxsat show"`.
+
+Full guide: `/usr/share/doc/chan-pbx-sat/HOWTO.md`.