bjorne
ec4b6127e7
- chan-pbx-sat: driver .so + pbx_sat.conf.sample (current config) + HOWTO. - pbxsat-freepbx: FreePBX web GUI (admin module + dashboard widget), deb arch=all / rpm noarch, deploys via fwconsole, depends on chan-pbx-sat. Debian 12/13 (bookworm/trixie) + CentOS/RHEL 7(ast16,ast18)/8/9. README updated.
61 lines
2.2 KiB
Markdown
61 lines
2.2 KiB
Markdown
# pbx_sat — prebuilt packages
|
|
|
|
Prebuilt **`.deb`** and **`.rpm`** packages for
|
|
**[pbx_sat](https://git.sa7aux.se/bjorne/pbx-sat)**, the direct PBX ↔ SVXReflector
|
|
bridge (`chan_pbx_sat`) — no AllStar in the path. Install these to build your own
|
|
PBX ↔ SVX trunk.
|
|
|
|
This repo holds **only built packages**, no source. The source lives in the
|
|
private `pbx-sat` repo. **x86_64 only** (PBX boxes are x86).
|
|
|
|
Two packages:
|
|
|
|
- **`chan-pbx-sat`** — the driver (`chan_pbx_sat.so`) + a sample
|
|
`/etc/asterisk/pbx_sat.conf` and the setup guide. Works on any Asterisk box.
|
|
- **`pbxsat-freepbx`** — the **FreePBX web GUI** (admin module *Connectivity →
|
|
PBX ⇄ SVX* + a dashboard status widget). Install it **too** on a FreePBX box;
|
|
it deploys into the web root via `fwconsole` and depends on `chan-pbx-sat`.
|
|
Not needed on a plain-Asterisk box (configure `pbx_sat.conf` by hand).
|
|
|
|
## Debian 12 / 13 (`debs/`)
|
|
|
|
```sh
|
|
# the driver (required):
|
|
sudo apt install ./debs/chan-pbx-sat_<version>~<suite>_amd64.deb
|
|
# the FreePBX GUI (on a FreePBX box):
|
|
sudo apt install ./debs/pbxsat-freepbx_<version>~<suite>_all.deb
|
|
```
|
|
|
|
`<suite>` is `bookworm` (Debian 12) or `trixie` (Debian 13). Built against the
|
|
box's Asterisk.
|
|
|
|
## CentOS / RHEL 7 / 8 / 9 (`rpms/`)
|
|
|
|
```sh
|
|
# the driver (required):
|
|
sudo dnf install ./rpms/chan-pbx-sat-<version>.<asttag>.<dist>.x86_64.rpm
|
|
# the FreePBX GUI (on a FreePBX box):
|
|
sudo dnf install ./rpms/pbxsat-freepbx-<version>.<asttag>.<dist>.noarch.rpm
|
|
```
|
|
|
|
One driver RPM per (distro, Asterisk major):
|
|
|
|
| File | Distro | Asterisk |
|
|
|------|--------|----------|
|
|
| `…ast22.el9…` | CentOS Stream 9 | 22 |
|
|
| `…ast22.el8…` | CentOS Linux 8 | 22 |
|
|
| `…ast18.el7…` | CentOS Linux 7 | 18 |
|
|
| `…ast16.el7…` | CentOS Linux 7 | 16 |
|
|
|
|
## After install
|
|
|
|
The driver does not load until you enable it:
|
|
|
|
1. `cp /etc/asterisk/pbx_sat.conf.sample /etc/asterisk/pbx_sat.conf` and edit it
|
|
(or use the FreePBX GUI if you installed `pbxsat-freepbx`).
|
|
2. Uncomment `load = chan_pbx_sat.so` in `/etc/asterisk/modules.conf`.
|
|
3. Point a dialplan route at `PBXSAT/<trunk>/<tg>`.
|
|
4. `asterisk -rx "core restart now"` then `asterisk -rx "pbxsat show"`.
|
|
|
|
Full guide: `/usr/share/doc/chan-pbx-sat/HOWTO.md`.
|